“Over time, we see Aster’s role developing further as an interface between global technology companies
and Indian manufacturers — bringing technology to India while providing local engineering, application
support, training and after-sales capabilities.”
1. Aster E Technologies supports solar PV manufacturing with turnkey solutions covering design, engineering, prototyping, and full-scale production. How does the company approach the integration of technology, equipment, and engineering to help manufacturers build efficient and cost-effective production lines?
Our approach is to integrate technology, equipment and engineering around the customer’s manufacturing objective rather than treating equipment supply as a standalone activity.
A solar manufacturing project requires the right combination of process technology, equipment selection, factory layout, utilities, automation, testing and quality-control systems. Aster works with customers from the early stage of technology and equipment selection through engineering, installation, commissioning, training and ongoing technical support.
Our portfolio spans a broad part of the PV value chain, including wafer, cell and module manufacturing solutions, solar simulators and IV testing, EL/PL inspection, characterisation and measurement, reliability laboratories and specialised testing systems. We also support module manufacturing with solutions such as laminators.
The objective is to create a production environment in which equipment, process parameters, inspection and testing work together. Accurate measurement and inspection are particularly important because manufacturers need timely feedback on defects, performance and process variation and validation.
We also work with technology partners to bring specialised solutions to the Indian market. This allows customers to access international technologies while receiving local project coordination, installation, training, application support and after-sales service.
Ultimately, our role is to help manufacturers build production capabilities that are efficient, repeatable and scalable, while also establishing the testing and engineering infrastructure needed for long-term manufacturing performance.
2. Your PV module manufacturing solutions are compatible with technologies such as MonoPERC, TOPCon, HJT, and G2G. How is Aster E Technologies helping manufacturers adapt their production infrastructure as cell and module technologies continue to evolve?
The PV industry is moving through rapid technology transitions, and manufacturers need production infrastructure that can adapt rather than become obsolete with every technology change.
Aster’s approach is to work with manufacturers on the technology and equipment requirements associated with different cell and module platforms, including MonoPERC, TOPCon, HJT, G2G and emerging Perovskite-based technologies.
At the module level, this means looking beyond the basic production line. Equipment selection has to consider module architecture, cell format, interconnection requirements, process control, inspection, lamination and final testing. We also support manufacturers with laminators, EL/PL inspection, IV testing and other testing and inspection technologies that help verify the quality of the finished module.
Our broader testing portfolio — including EL/PL inspection, IV testing, solar simulation, environmental chambers, spectrometers and reliability testing — provides manufacturers with the measurement infrastructure required as designs and technologies evolve.
At the same time, we see Perovskite and Perovskite-Silicon Tandem as important emerging technologies for the next generation of high-efficiency PV. Aster is already supporting R&D and pilot-scale Perovskite solutions, helping create a pathway from laboratory development towards scalable manufacturing. We believe that India’s manufacturing ecosystem should start building capabilities in these technologies today rather than waiting until they become fully mature commercially.
We believe flexibility is increasingly important. Manufacturers need the ability to upgrade equipment, modify process parameters and introduce new products while maintaining yield and quality.
Aster therefore combines equipment and technology access with engineering, commissioning, training and lifecycle support. Our objective is to help manufacturers manage technology transitions in a controlled manner while protecting production quality and equipment utilisation — and at the same time prepare for the next generation of PV technologies.
3. Aster E Technologies has established 45+ turnkey reliability laboratories and offers testing solutions covering standards such as IEC 61215, IEC 61730, IEC 61701, UL 1703, and BIS. What role do advanced testing and reliability laboratories play in improving the quality and long-term performance of solar modules?
Reliability testing is essential because a solar module is expected to operate for many years under changing environmental conditions. Manufacturing quality therefore cannot be assessed only by initial power output.
A properly designed reliability laboratory allows manufacturers to evaluate how a module behaves under environmental, mechanical and material stresses and to identify potential failure mechanisms before products are deployed at scale.
Aster has established 45+ turnkey reliability laboratories and provides solutions covering a range of qualification and reliability requirements, including standards such as IEC 61215, IEC 61730, IEC 61701, UL 1703 and BIS, as referenced in the questionnaire.
Our laboratory solutions can include environmental testing such as thermal cycling, humidity freeze, damp heat, PID, UV and LETID, together with mechanical and material testing. The exact configuration is selected according to the customer’s products, standards and development objectives.
We see the laboratory not simply as a compliance facility, but as a product-development and manufacturing-improvement tool. Test results can help manufacturers identify material, design or process weaknesses and feed that information back into engineering and production.
As module technologies evolve, particularly with higher power, new cell architectures and emerging technologies, reliable testing and characterisation become increasingly important for demonstrating product quality and long-term performance.
4. The company offers solar cell metrology and testing solutions including Cell IV testers, EL/PL imaging, contact resistivity testers, and LED-based sun simulators. How do these technologies help manufacturers identify performance and quality issues and improve manufacturing processes?
The value of metrology and testing is that they convert manufacturing output into measurable process information.
Cell IV testing provides quantitative information on electrical performance, while EL and PL imaging can reveal defects and non-uniformities that may not be visible through conventional inspection. Contact resistivity measurement helps evaluate electrical contact performance, while solar simulators provide controlled and repeatable conditions for performance measurement.
Aster’s portfolio also includes technologies such as spectrometers and other characterisation and measurement systems. Together, these tools allow manufacturers to build a more complete picture of cell and module performance.
The key benefit is the ability to connect measurement results with manufacturing processes. If a recurring defect or performance deviation is identified, manufacturers can investigate the relevant process step, correct the issue and then verify the improvement through measurement.
This creates a continuous improvement loop:
Manufacturing → Measurement → Inspection → Analysis → Process Correction → Verification.
For high-volume manufacturing, this is particularly important because even small variations can affect yield and overall production economics.
Our role is therefore not only to supply testing equipment, but to help customers establish the measurement and inspection infrastructure needed for stable, high-quality manufacturing.
5. Aster E Technologies has expanded its turnkey portfolio to include perovskite and tandem solar technologies, from laboratory research to production. What opportunities do you see for these next-generation technologies, and how is Aster supporting customers in moving from R&D towards scalable manufacturing?
We see perovskite as one of the important technologies in the next phase of photovoltaic development, particularly when combined with silicon in tandem architectures.
The opportunity is not simply to achieve higher laboratory efficiency, but to translate that performance into stable, reliable and scalable manufacturing. Perovskite/silicon tandem structures are particularly interesting because they can build on the existing silicon PV ecosystem while introducing an additional high-efficiency photovoltaic layer.
Aster has already introduced turnkey and standalone R&D and pilot-line solutions for perovskite technology in India. Our technology portfolio covers areas such as single-junction perovskite, perovskite/silicon tandem development, slot-die coating, inkjet printing, ALD, VCD/annealing, laser scribing and thermal evaporation.
We believe India needs to invest in this technology and build domestic capability in R&D, pilot manufacturing, characterisation and reliability. International investment in perovskite is increasing, and India has an opportunity to participate in the development of the technology rather than only adopting it later.
The pathway we see is R&D → pilot line → process optimisation → reliability and characterisation → scale-up.
Aster’s role is to provide the equipment and engineering ecosystem that supports this progression, while helping customers connect process development with measurement, inspection and reliability requirements.
We are also interested in specialised applications such as Space PV, where advanced characterisation, environmental testing and reliability are particularly important.
6. Your portfolio also includes end-to-end ingot-to-wafer manufacturing solutions covering crystal growth, squaring, grinding, slicing, and wafer processing. How important is the development of upstream manufacturing capabilities for building a more integrated and technologically capable solar manufacturing ecosystem?
Upstream manufacturing is an important part of building a deeper and more resilient solar manufacturing ecosystem.
If India wants to increase domestic manufacturing capability, the value chain cannot remain concentrated only at the module level. Greater capability in ingot and wafer manufacturing can strengthen supply-chain integration and provide manufacturers with greater control over critical process steps and material quality.
Our ingot-to-wafer portfolio covers the stages referenced in our offering, including crystal growth, squaring, grinding, slicing and wafer processing. The objective is to connect upstream processes with the requirements of downstream cell manufacturing.
Upstream integration also creates opportunities to improve process control, material utilisation, quality consistency and manufacturing economics. At the same time, these projects require substantial process expertise, utilities, equipment integration and engineering support.
Aster’s role is to connect technology providers with Indian manufacturers and support the project from technology and equipment selection through installation, commissioning, training and operational support.
We also see sustainability and resource efficiency becoming increasingly important in upstream manufacturing. Technologies such as argon recovery and purification can help reduce gas consumption and operating costs in silicon ingot-pulling applications.
Developing upstream capabilities, therefore, is not only about adding another manufacturing stage. It is about creating a more integrated, technically capable and sustainable PV manufacturing ecosystem in India.
7. Beyond equipment supply, Aster E Technologies provides services covering raw-material and supply-chain support, facility layout, technology and equipment selection, production planning, training, and AMC/O&M support. How do you see this end-to-end approach evolving as solar manufacturers seek long-term technology, operational, and manufacturing partners?
We believe the relationship between manufacturers and technology providers is moving from transactional equipment supply towards long-term technology and engineering partnerships.
As manufacturing capacities become larger and technologies evolve faster, customers need support throughout the project lifecycle. This includes technology selection, equipment selection, factory planning, installation, commissioning, production planning, training, process support, spare-parts management and AMC/O&M.
Aster’s objective is to provide this continuity. Our engineering and service teams work with customers beyond the initial equipment delivery, helping coordinate installation, training, technical support and lifecycle requirements.
We also see increasing importance in local service infrastructure. High equipment utilisation depends on timely troubleshooting, preventive maintenance and availability of critical spares. For manufacturers operating at large scale, reducing downtime can be as important as the initial equipment specification.
The same approach applies to emerging technologies. Perovskite, tandem PV and specialised applications such as Space PV require closer collaboration between technology suppliers, equipment providers, R&D teams and manufacturers because the processes are still evolving.
Over time, we see Aster’s role developing further as an interface between global technology companies and Indian manufacturers — bringing technology to India while providing local engineering, application support, training and after-sales capabilities.
Our long-term objective is to be a technology and engineering partner throughout the manufacturing lifecycle, rather than simply a supplier at the point of purchase.


